Kawasaki KMX15YD-B44031D LC30V00028F4 hydraulic control valve for Kobelco SK350-8 excavator
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
+86 189 289...
+86 189 2896 5241
China
China
China
China
China
China
China
China
China
China, Guangzhou
China
Netherlands, Wouw
Netherlands, Wouw
Netherlands, Wouw
Romania, Targu Mrues
Romania, Targu Mrues
Product Overview
On a 35‑ton machine, hydraulic oil is not an incidental consumable — it is a large, expensive volume that the owner replaces on a schedule. What most owners do not connect is that a worn control valve accelerates that schedule. Oil forced through leaking spools gains heat without doing work, and heat is what oxidises oil, shortens filter life and pushes drain intervals closer together. The SK350‑8's hydraulic main valve, reference LC30V00028F4, sits at the centre of that relationship: it divides pump flow among boom, arm, bucket, swing and travel, and how well it seals decides how hard the oil has to work.
The operational symptoms arrive alongside the oil cost. The boom sags on a held bucket. The arm loses bite at the bottom of a cut. Swing lands short. Tracks bog on the ramp with a full bucket. Each one is oil crossing between circuits past worn spools. This aftermarket main valve replaces the block complete with fresh internals set to Kobelco ‑8 values, so the worn unit comes off in one piece and the replacement fits the original port positions.
Core Advantages
1. Oil stops being cooked by internal leakage
Leakage turns pump output into heat. Restored clearances reduce the thermal load on a large oil charge, which is where the hidden operating cost sits.
2. Drain intervals return to the book figure
Owners who shorten oil changes to protect a worn machine can go back to the specified interval once the source of heat is removed.
3. Force returns at the cutting edge
Renewed spools put pressure back into the arm and bucket, so the machine bites instead of labouring.
4. Full buckets stay over the body
A sagging boom forces a re‑spot each pass. Restored retention keeps the load where it was placed.
5. Complete assembly rather than circuit‑by‑circuit repair
One tested block resolves every drifted circuit, which on a machine this size is measured against downtime cost rather than parts cost.
Manufacturing & Quality Control
Spool and bore pairs are machined to print tolerance, matched by size, and hand‑run‑in until full‑stroke movement is free of binding. Assembled blocks are flow‑tested circuit by circuit with relief and compensator values logged against ‑8 figures; out‑of‑window units are stripped and corrected. Blocks ship internally oil‑fogged, ports capped, and crated on foam.
Frequently Asked Questions
Q1: How do I confirm LC30V00028F4 suits my SK350‑8?
A: Send a photo of the tag on the existing valve with the machine serial number. Build variants exist across the ‑8 run and we verify before dispatch.
Q2: Is rising oil temperature really linked to the valve?
A: It often is. Internal leakage converts pressure into heat without producing work. Before adding coolers, check the block with a circuit leak test.
Q3: What symptoms indicate valve wear?
A: Boom drift on held loads, lost bite at the bottom of a cut, inconsistent swing placement, and travel that reacts to bucket load. A leak test confirms.
Q4: Can my existing block be rebuilt?
A: If the casting is sound and has never been rebuilt, a kit may restore it. Where several circuits leak, a complete assembly usually gives better service per dollar. Photos help us judge.
Q5: What servicing belongs with the swap?
A: Flush the system, renew the return filter, clean the suction strainer, and refill with specified oil. On a 35‑ton machine the oil charge is significant, so plan the volume in advance.
Q6: What is excluded from warranty?
A: Material and assembly faults are covered. Damage from dirty oil, water ingress, a spool forced against a bind, or reliefs altered outside specification is not. Photograph the crate before opening if damage is visible.